Filling a bathtub properly

How to outsmart the bathtub overflow

Author: C.H., Lichtenstein/Sachsen

Online since: 18/06/2010, Number of visits: 150724

My bathtub is simply too small! Those were my exact thoughts when I recently tried to enjoy a good soak in my tub – which, with its low water level, feels more like a sitz bath. Since neither my landlord nor my wallet would appreciate it if I were to rip the tub out and replace it with a larger one, I had to find a different solution.

My idea: It should be possible to somehow increase the water level in the bathtub. The problem is the overflow, which in my opinion is placed far too low. So I wanted to build an overflow cover that could be mounted and removed easily and would allow me to fill the tub all the way to the top.

Materials needed:

Front part of a plunger
1 block magnet each of type Q-20-20-10-N and Q-15-15-08-N
Silicone
Adhesive UHU MAX REPAIR

Assembly:

First, I inserted a Q-20-20-10-N into the front part of the plunger (where the wooden handle used to be) and sealed it with silicone.

Note from the supermagnete team:
Instead of the block magnet, it may be advisable to use a disc magnet with the same diameter as the indentation.

Opening of the plunger filled with silicone

Inside of the turning handle with a glued-in block magnet

As a counterpart, I glued a Q-15-15-08-N inside the turning handle of the tub, using UHU MAX REPAIR.

Important! Don’t skimp on the glue and silicone, since the magnets will quickly start to rust.

Next, I only had to put the turning handle back on the tub.

Now, before getting into the tub, I can simply place the magnetic plunger over the turning handle, which will seal off the overflow.

To drain the tub, I just remove the plunger and open the plug by turning the handle.

The water in the tub rises above the cover

The water rises higher...

Thanks to the overflow cover, the tub is almost completely filled with water

...almost to the rim of the bathtub

Articles used

Q-15-15-08-N

Block magnet 15 x 15 x 8 mm, holds approx. 7,6 kg, neodymium, N42, nickel-plated

	1 pc.	3,60 EUR ea.*
from	3 pcs.	3,14 EUR ea.*
from	10 pcs.	2,73 EUR ea.*
from	20 pcs.	2,53 EUR ea.*
from	40 pcs.	2,36 EUR ea.*
Ask for a rebate from 240 pcs.

Receive e-mail when item available again

Q-20-20-10-N

Block magnet 20 x 20 x 10 mm, holds approx. 12 kg, neodymium, N42, nickel-plated

	1 pc.	5,94 EUR ea.*
from	3 pcs.	5,28 EUR ea.*
from	10 pcs.	4,71 EUR ea.*
from	20 pcs.	4,42 EUR ea.*
from	40 pcs.	4,17 EUR ea.*
Ask for a rebate from 350 pcs.

Available: 31 710 pcs.

UHU MAX REPAIR

magnet glue, waterproof, without solvents, shelf life of 24 months, 20 g tube
To glue on super magnets

1 pc. 8,15 EUR ea.* (407,50EUR/kg)

Available: 2 334 pcs.

0 people like this customer project -Projects are bookmarked in your customer account

This might also interest you

Catching drill chips

Hanging a poster on a sloping ceiling

Necklace clasp

Pocket knife trick

keywords

Tips+tricks ( 51 )
Attaching ( 136 )
Plastic ( 46 )
Magnet closure ( 24 )
Bathroom ( 20 )
Low priced ( 161 )
Easy ( 200 )
Large magnets ( 44 )
Useful ( 234 )

The entire content of this site is protected by copyright.
Copying the content or using it elsewhere is not permitted without explicit approval.